Black Revel Speakers and Subwoofers
Shop Speakers and Subwoofers by Type
- 10 (25.4 cm) coated paper/pulp cone woofer
- Inputs: balanced (XLR) and unbalanced (RCA)
- Input sensitivity/impedance: 400mV (full power)/20k ohms balanced; 14k ohms (unbalanced)
- Crossover frequency: 50Hz - 150Hz low pass filter with LFE bypass
- Dimensions: (H x W x D): 16.875 x 14.31 x 13.44 (42.8cm x 36.4cm x 34.2cm)
- Weight: 53.8 lb (24.4 kg)
- Rounded baffles and enclosures virtually eliminate diffraction
- Woofer and midrange trandsducers feature inverted-dome designs for superior piston like behavior
- Tweeters use acoustically optimized waveguides for seamless transitions between the tweeter and midrange
- Pure-beryllium dome tweeters exhibit the optimal balance of high-power handling, low distortion and compression
- Separate filter boards for each frequency range
- Ideally suited for use as a LCR loudspeaker
- Due to lighting and monitor differences, actual colors and finishes may vary slightly from what appears online
- Long-throw woofers with rubber surrounds provide high output with low distortion
- 1-inch (25mm) metal-dome tweeter with an integrated waveguide provides optimized response both on and off axis
- High-order crossover network delivers accurate timbre reproduction
- Boundary compensation switch (W893/W873/W783/W763) lets you adjust the speaker to maintain tonal accuracy when the speaker is placed near an additional wall or the ceiling
- Three-position tweeter level control (W893/W873/W783/W763/W583/W563/W553L) lets you adjust for optimum response in a variety of acoustical environments or for using the speakers without grilles
- Due to lighting and monitor differences, actual colors and finishes may vary slightly from what appears online
- Transducers feature motor-system distortion-reduction mechanisms that stabilize the flux field during operation
- Ribbed aluminum cones achieve piston like behavior eliminating major sources of resonance
- New waveguides provide consistent sound over a wide listening area
- Enclosures created by Italian luxury cabinetmakers
- Fluid-model port designs keep distortion low
- Advanced crossovers optimize timbre accuracy both on axis and throughout the room
- Two 6.5 (165mm) Deep Ceramic Composite aluminum cone with cast frame woofers
- 5.25 (130mm) Deep Ceramic Composite aluminum cone midrange
- 1 (25mm) Beryllium dome tweeter
- Recommended Amplifier Power: 50-200 Watts
- Frequency Response: 44Hz 40kHz (-6dB)
- Nominal Impedance: 8 ohms
- Loudspeaker Sensitivity (2.83V/1m): 90dB
- Crossover Frequencies: 260Hz; 2.1kHz
- Dimensions (H x W x D): 41.3 x 9.8 x 13.7 (1050mm x 249mm x 347mm)
- Weight: 58.8 lbs (26.8kg)
Suggested Retail
$880.00
$616.00 On Sale
Save $264.00
- Derived from Revel's award-winning Performa3 Series Loudspeakers
- 5.25"deep anodized aluminum cone woofers
- 1" Aluminum Tweeter
- Fourth generation Acoustic Lens waveguides
- Computer optimized driver positioning and network integration
- Constant pressure gradient port design
- No visible fasteners on the front, top or side panels
- Magnetic grilles with brushed metallic logos
- Due to lighting and monitor differences, actual colors and finishes may vary slightly from what appears online
$825.00 Mart Price
- 4-inch/100mm Micro Ceramic Composite (MCC) aluminum diaphragm woofer
- 3/4-inch/19mm Micro Ceramic Composite (MCC) aluminum diaphragm tweeter
- IP67 rating that certifies protection against dust and strong water jets and waves
- 4-Ohm or 70V operation via integrated transformer with selectable power taps up to 60W
- Sliding clamp assembly allows you to adjust the center of gravity
- Due to lighting and monitor differences, actual colors and finishes may vary slightly from what appears online
- Dual 8 (20 cm) Aluminum Cone, Cast- frame Woofers
- 5.25 (13.3 cm) Aluminum Cone, Cast- frame Midrange
- 1 (2.5 cm) Aluminum Tweeter with Acoustic Lens Waveguide
- Recommended amplifier power range: 50 350 watts
- Low-frequency extension: 23Hz (10dB); 27Hz (6dB); 31Hz (3dB)
- Nominal impedance: 8 ohms
- Sensitivity (2.83V/1m): 88.5dB
- Enclosure type: Bass-reflex via front-mounted port
- Controls: Low-frequency contour; high-frequency level
- Inputs: Dual gold-plated binding posts with shorting straps
- Dimensions (H x W x D): 46.5 x 11.8 x 14.8 (118.2 cm x 30 cm x 37.5 cm)
- Weight: 80 lb (36 kg) / Packaged weight: 87 lb (39.6 kg)
- Packaged dimensions (H x W x D): 50.2 x 17.7 x 21.5 (127.5 cm x 45 cm x 54.5 cm)
- Dual 8 (20 cm) Aluminum Cone, Cast- frame Woofers
- 4 (10 cm) Aluminum Cone, Cast-frame Midrange
- 1 (2.5 cm) Aluminum Tweeter with Acoustic Lens Waveguide
- Recommended amplifier power range: 50 350 watts
- Low-frequency extension: 34Hz (10dB); 41Hz (6dB); 50Hz (3dB)
- Nominal impedance: 8 ohms
- Sensitivity (2.83V/1m): 89dB
- Enclosure type: Sealed
- Controls: Low-frequency contour; high-frequency level
- Inputs: Dual gold-plated binding posts with shorting straps
- Dimensions (H x W x D): 11.8 x 28.9 x 13.8 (30 cm x 73.5 cm x 35 cm)
- Weight: 52 lb (23 kg) / Packaged weight: 55 lb (24.9 kg)
- Packaged dimensions (H x W x D): 15.9 x 32.3 x 20.5 (40.5 cm x 82 cm x 52 cm)
$2,200.00 Mart Price
- 6.5 (165mm) Deep Ceramic Composite (DCC) aluminum cone woofer with cast frame
- 1 (25mm) Beryllium dome tweeter with acoustic lens waveguide
- Recommended Amplifier Power: 50 150 Watts
- Nominal Impedance: 8 ohms
- Loudspeaker Sensitivity (2.83 V/1m): 86dB
- Frequency Response: 54Hz 44kHz (-6dB)
- Crossover Frequency: 1.7kHz
- Dimensions (H x W x D): 15.2 x 8.3 x 10.3 (386 x 211 x 262mm)
- Weight: 22 lbs (9.97kg)
- Packaged dimensions (H x W x D): 19 x 12.3 x 16.3 (483 x 311 x 413mm)
- Packaged weight: 26 lbs (11.6 kg)
- Inputs:Gold-plated binding posts
- Three 8 (20 cm) titanium cone woofers
- 6 (16.5 cm) titanium cone mid-woofer
- 4 (10 cm) titanium cone midrange
- 1 (2.5 cm) beryllium tweeter
- Sensitivity 86.4 dB SPL with 2.83 V @ 1m (4 pi anechoic)
- Impedance 6 ohms (nominal) 3.7 ohms (minimum @ 90 Hz)
- Frequency Range - 3 dB from 23 Hz to 45 kHz
- Dimensions (H x W x D): 53.3 x 14 x 23 (135.4 cm x 35.6 cm x 58.4 cm)
- Weight: 146 lb (66.3 kg)
- Packaged dimensions (H x W x D): 58.1 x 17.6 x 32.1 (147.5 cm x 44.7 cm x 81.5 cm)
- Packaged weight: 182.54 lb (82.8 kg)
- Vertically oriented 2-way loudspeakers for 2-channel or surround systems
- Horizontally oriented center channel with table cradle and bracket (SP5 only)
- Micro Ceramic Composite (MCC) diaphragms
- Sophisticated high-frequency waveguides
- Precision dividing networks
- Magnetic shielding for safe placement near electronic devices
- Included mounting hardware
- Three automotive grade high gloss finishes
- Due to lighting and monitor differences, actual colors and finishes may vary slightly from what appears online
- 8" down-firing cone transducer
- Built-in high-performance 200-watt RMS amplifier
- Wireless 2.4GHz audio signal transmission
- Two automotive-grade finishes
- Due to lighting and monitor differences, actual colors and finishes may vary slightly from what appears online
- Dual 6.5 (16.5 cm) Aluminum Cone, Cast- frame Woofers
- 1 (2.5 cm) Aluminum Tweeter with Acoustic Lens Waveguide
- Recommended amplifier power range: 50 150 watts
- Low-frequency extension: 52Hz (10dB); 58Hz (6dB); 65Hz (3dB)
- Nominal impedance: 8 ohms
- Sensitivity (2.83V/1m): 89dB
- Crossover frequency: 1.4kHz
- Enclosure type: Sealed
- Inputs: Gold-plated binding posts
- Dimensions (H x W x D): 13.5 x 15.8 x 8.5 (34.3 cm x 40 cm x 21.6 cm)
- Weight: 16 lb (7 kg) Packaged dimensions (H x W x D): 13 x 20.3 x 18.5 (330 x 515 x 470mm)
- Packaged weight: 21 lb (9.5 kg)
$4,950.00 Mart Price
- 1-inch beryllium dome tweeter
- 5th-generation Acoustic Lens waveguide
- Deep ceramic composite (DCC) cone midrange and woofers
- High-order crossovers with film capacitors and air core inductors
- Magnetically attached grilles
- Due to lighting and monitor differences, actual colors and finishes may vary slightly from what appears online
- Transducers feature motor-system distortion-reduction mechanisms that stabilize the flux field during operation
- Ribbed aluminum cones achieve piston like behavior eliminating major sources of resonance
- New waveguides provide consistent sound over a wide listening area
- Enclosures created by Italian luxury cabinetmakers
- Fluid-model port designs keep distortion low
- Advanced crossovers optimize timbre accuracy both on axis and throughout the room
- Due to lighting and monitor differences, actual colors and finishes may vary slightly from what appears online
- Transducers feature motor-system distortion-reduction mechanisms that stabilize the flux field during operation
- Ribbed aluminum cones achieve piston like behavior eliminating major sources of resonance
- New waveguides provide consistent sound over a wide listening area
- Enclosures created by Italian luxury cabinetmakers
- Fluid-model port designs keep distortion low
- Advanced crossovers optimize timbre accuracy both on axis and throughout the room
- Due to lighting and monitor differences, actual colors and finishes may vary slightly from what appears online
Suggested Retail
$825.00
$577.50 On Sale
Save $247.50
- Derived from Revel's award-winning Performa3 Series Loudspeakers
- 5.25"deep anodized aluminum cone woofers
- 1" Aluminum Tweeter
- Fourth generation Acoustic Lens waveguides
- Computer optimized driver positioning and network integration
- No visible fasteners on the front, top or side panels
- Magnetic grilles with brushed metallic logos
- High-gloss Black and High-gloss White painted finishes
- Due to lighting and monitor differences, actual colors and finishes may vary slightly from what appears online
- Dual 8 (200mm) Deep Ceramic Composite (DCC) aluminum cone woofers with cast frames
- 5.25 (130mm) DCC aluminum cone midrange with cast frame
- 1 Beryllium dome tweeter with acoustic lens waveguide
- Recommended Amplifier Power: 50 350 Watts
- Nominal Impedance: 8 ohms
- Loudspeaker Sensitivity (2.83 V/1m): 90dB
- Frequency Response: 27Hz 44kHz (-6dB)
- Crossover Frequency: 260Hz; 2.1kHz
- Dimensions (H x W x D): 46.5 x 11.8 x 13.2 (1181 x 302 x 335mm)
- Weight: 82 lbs (37.2kg)
- Packaged dimensions (H x W x D): 52.8 x 19.5 x 23.7 (1340 x 495 x 603mm)
- Packaged weight: 112 lbs (50.9 kg)
- Inputs: Dual gold-plated binding posts with shorting straps
- Flagship floorstander for the PerformaBe range
- 1-inch beryllium dome tweeter
- 6th-generation Acoustic Lens waveguide
- Deep ceramic composite (DCC) cone midrange and woofers
- High-order crossovers with film capacitors and air core inductors
- Magnetically attached grilles
- Due to lighting and monitor differences, actual colors and finishes may vary slightly from what appears online
- Onboard Parametric Equalization (PEQ) system
- 50mm two layer copper voice coil for very high Xmax and dramatically increased output
- High temperature Nomex spider for even distribution of mechanical stress
- Oversized SBR rubber surround for greater linear excursion
- Vented cellulose/pulp cone and cast aluminum frame for reduced acoustic loss
- Due to lighting and monitor differences, actual colors and finishes may vary slightly from what appears online
Suggested Retail
$1,100.00
$770.00 On Sale
Save $330.00
- Derived from Revel's award-winning Performa3 Series Loudspeakers
- 6.5"deep anodized aluminum cone woofers
- 1" Aluminum Tweeter
- Fourth generation Acoustic Lens waveguides
- Computer optimized driver positioning and network integration
- Constant pressure gradient port design
- No visible fasteners on the front, top or side panels
- Magnetic grilles with brushed metallic logos
- Due to lighting and monitor differences, actual colors and finishes may vary slightly from what appears online
- 12-inch / 305mm durable aluminum cone woofer
- Stealth design - only the bass vent canopy is visible
- IP67 rating on the underground enclosure; IP43 rating on the above-ground canopy
- 6-Ohm or 70V operation via external transformer with selectable power taps up to 250W
- Composite housing with aluminum canopy and polymer port tube stack
- Due to lighting and monitor differences, actual colors and finishes may vary slightly from what appears online